|
You have to see this car in person... Pictures can't show 1/10 of detail and custom work. 1969 Camaro Ultimate Pro Touring build. Over $210, 000 invested. Tons of body mods and a lot of hand made metal. A must see. Hand made metal hood. Hand made grill with wire mesh. Hand made front and rear bumpers that are both french-ed into the body. Nickel plated Hand made metal rear spoiler. Block and primed 5 times. Hand made cowl panel. On and on..... Chassis: Art Morrison complete full frame. New 1 off Art Morrison full frame, 1 piece. It is channeled up into the body and has custom exhaust that runs through it for maximum ground clearance. You can still remove the body off the frame. Front suspension: Corvette C-5 front suspension. All New Not downer car. All polished for show. Spline sway bar. Rack and pinion steering, also polished. WilWood 14" 2 piece rotors and 6 piston calipers. Rear suspension: Corvette C-4 IRS. Completely built to handle over 1000hp. Over-sized axles and yokes. Also polished. QA1 coil over. Spline sway bar as well. Polished 1/2 shafts and drive line also. Stainless brake lines. All custom floors, raised for frame to get channeled into body. Looks great. Painted bottom side and inside. Engine: LS7 (427) All aluminum. (new) All new, nothing used. Should dyno around 780 hp. AFR (230) polished heads that are also ported and polished. Billet Kings crank. Titanium rods. JE pistons. Peterson custom oil tank and there breather kit as well. Custom Stack fuel injection system. Cost $4, 500 alone. 1 off custom air cleaner and stainless pipe that runs to lower front air dam to draw cold air in. Air cleaner set up was all hand made and cost over $6, 000. Once you see it you will know why. All polished vintage Air belt set up. Gen 4 Vintage A/C. Fast EFI engine harness and engine managment system with display screen. Transmission: Customs built T56 6 speed. Also polished out. New billet flywheel. Dual friction clutch. Custom Scatter shield also polished. Hand made headers, coated. Hand made complete exhaust system. All joints are V bands for easy fast removal. Custom hand made stainless gas tank. With built in fuel pump. DSE billet hood hinges. Ring brothers Billet door striker. Marqez Billet tail lights. Degi-tail Led turn signals. Marqez design Billet market lights. Custom built aluminum radiator with dual fans. Custom built aluminum A/c condenser. Electric life power windows front and rear. Hand made dash. 1 off custom gauges. Hand made dash and doors panels. Hand made center console. Way to much to list.. New American Auto Wire car wiring harness. New Ididit push button start system. Completely wired in. Dynomat the complete car. Car was also painted inside and out, then truck bed liner on the inside of the doors and trunk and quarters. All new smoked glass, ready to be installed. New Fast EFI engine harness and ecm and hand held. May do part trade.... There is so much done to this car, best is to call or come out and see the car. Please check out my other auctions. Yes, i have a had made custom hood to match the car, it is smoothed and painted to match. Also all the custom engine covers and inner fenders are also at the body shop. They are all hand made and look amazing. Also painted Black to match. This is a must see, all the detail and hand made parts are over the top. I have a ton of parts that go with the car. Not seen in the pictures. Billet hood hinges, custom hood, all engine covers and inner fender wells, all hand made and painted. L.E.D tail lights, BMW power heated seats, Custom mesh that is also nickel plated that goes in other areas of the car, bolt in power windows, the factory wire boots for the p/w and the wholes are pre-drilled in the car and doors, New Fast EFI complete engine management system, custom hand made stainless gas tank with baffle and built in pump, 2 billet battery mounts (already installed), Custom made G.M power door poppers (installed), Hand made billet pedals (installed), Billet headlight switch (installed), 6 piston front brakes, 1-off billet 6 speed shifter (not installed), all metal custom center console, Custom door panels to match dash that are at the body shop, complete set of glass for the car and it is all smoked, all New seals and felts, new window stainless, power trunk actuator (installed), new door sill plates, new starter (installed). There is way more then listed and this was just off the top of my head. I have tons of parts. Just got done in the last 4 weeks. -I got the whole trunk, inside the quarter panels and inside the door's, painted with Truck Bed Liner. -Floor Dyno
|
